Configuration Options for 18F2423

   Oscillator Selection:
     OSC = LP             LP Oscillator
     OSC = XT             XT Oscillator
     OSC = HS             HS Oscillator
     OSC = EC             External Clock on OSC1, OSC2 as Fosc/4
     OSC = ECIO6 	  EC oscillator, port function on RA6
     OSC = HSPLL 	  HS oscillator, PLL enabled (Clock Frequency = 4 x FOSC1)
     OSC = RCIO6 	  External RC oscillator, port function on RA6
     OSC = INTIO67 	  Internal oscillator block, port function on RA6 and RA7
     OSC = INTIO7 	  Internal oscillator block, CLKO function on RA6, port function on RA7

   Fail Safe Clock Monitor:
     FSCM = OFF           Fail Safe Clock Monitor disabled
     FSCM = ON            Fail Safe Clock Monitor enabled

   Internal External Switch Over mode:
     IESO = OFF           Internal External Switch Over mode disabled
     IESO = ON            Internal External Switch Over mode enabled

   Power-Up Timer:
     PWRT = ON            Enabled
     PWRT = OFF           Disabled

   Brown-Out Reset:
     BOREN = OFF 	  Brown-out Reset disabled in hardware and software
     BOREN = ON 	  Brown-out Reset enabled and controlled by software (SBOREN is enabled)
     BOREN = NOSLP 	  Brown-out Reset enabled in hardware only and disabled in Sleep mode (SBOREN is disabled)
     BOREN = SBORDIS 	  Brown-out Reset enabled in hardware only (SBOREN is disabled)

   Brown Out Voltage:
     BORV = 0 		Maximum setting
     BORV = 1 
     BORV = 2 
     BORV = 3 		Minimum setting

   Watchdog Timer:
     WDT = OFF            Disabled
     WDT = ON             Enabled

   Watchdog Postscaler:
     WDTPS = 1            1:1
     WDTPS = 2            1:2
     WDTPS = 4            1:4
     WDTPS = 8            1:8
     WDTPS = 16           1:16
     WDTPS = 32           1:32
     WDTPS = 64           1:64
     WDTPS = 128          1:128
     WDTPS = 256          1:256
     WDTPS = 512          1:512
     WDTPS = 1024         1:1024
     WDTPS = 2048         1:2048
     WDTPS = 4096         1:4096
     WDTPS = 8192         1:8192
     WDTPS = 16384        1:16384
     WDTPS = 32768        1:32768

MCLR Pin Enable bit:
	MCLRE = OFF 	RE3 input pin enabled; MCLR disabled
	MCLRE = ON 	MCLR pin enabled; RE3 input pin disabled

Low-Power Timer1 Oscillator Enable bit:
	LPT1OSC = OFF 	Timer1 configured for higher power operation
	LPT1OSC = ON 	Timer1 configured for low-power operation

PORTB A/D Enable bit:
	PBADEN = OFF 	PORTB<4:0> pins are configured as digital I/O on Reset
	PBADEN = ON 	PORTB<4:0> pins are configured as analog input channels on Reset

CCP2 MUX bit:
	CCP2MX = PORTB 	CCP2 input/output is multiplexed with RB3
	CCP2MX = PORTC 	CCP2 input/output is multiplexed with RC1

Stack Full/Underflow Reset Enable bit:
	STVREN = OFF 	Stack full/underflow will not cause Reset
	STVREN = ON 	Stack full/underflow will cause Reset

Low Voltage ICSP:
	LVP = OFF 	Disabled
	LVP = ON 	Enabled

Extended Instruction Set Enable bit:
	XINST = OFF 	Instruction set extension and Indexed Addressing mode disabled (Legacy mode)
	XINST = ON 	Instruction set extension and Indexed Addressing mode enabled

Background Debugger Enable bit:
	DEBUG = ON 	Background debugger enabled, RB6 and RB7 are dedicated to In-Circuit Debug
	DEBUG = OFF 	Background debugger disabled, RB6 and RB7 configured as general purpose I/O pins

Code Protection Block 0:
	CP0 = ON 	Block 0 (000800-001FFFh) code-protected
	CP0 = OFF 	Block 0 (000800-001FFFh) not code-protected

Code Protection Block 1:
	CP1 = ON 	Block 1 (002000-003FFFh) code-protected
	CP1 = OFF 	Block 1 (002000-003FFFh) not code-protected

Boot Block Code Protection bit:
	CPB = ON 	Boot block (000000-0007FFh) code-protected
	CPB = OFF 	Boot block (000000-0007FFh) not code-protected

Data EEPROM Code Protection:
	CPD = ON 	Data EEPROM code-protected
	CPD = OFF 	Data EEPROM not code-protected

Write Protection Block 0:
	WRT0 = ON 	Block 0 (000800-001FFFh) write-protected
	WRT0 = OFF 	Block 0 (000800-001FFFh) not write-protected

Write Protection Block 1:
	WRT1 = ON 	Block 1 (002000-003FFFh) write-protected
	WRT1 = OFF 	Block 1 (002000-003FFFh) not write-protected

Boot Block Write Protection bit:
	WRTB = ON 	Boot block (000000-0007FFh) write-protected
	WRTB = OFF 	Boot block (000000-0007FFh) not write-protected

Configuration Register Write Protection bit:
	WRTC = ON 	Configuration registers (300000-3000FFh) write-protected
	WRTC = OFF 	Configuration registers (300000-3000FFh) not write-protected

Data EEPROM Write Protection bit:
	WRTD = ON 	Data EEPROM write-protected
	WRTD = OFF 	Data EEPROM not write-protected

Table Read Protection Block 0:
	EBTR0 = ON 	Block 0 (000800-001FFFh) protected from table reads executed in other blocks
	EBTR0 = OFF 	Block 0 (000800-001FFFh) not protected from table reads executed in other blocks

Table Read Protection Block 1:
	EBTR1 = ON 	Block 1 (002000-003FFFh) protected from table reads executed in other blocks
	EBTR1 = OFF 	Block 1 (002000-003FFFh) not protected from table reads executed in other blocks

Boot Block Table Read Protection bit:
	EBTRB = ON 	Boot block (000000-0007FFh) protected from table reads executed in other blocks
	EBTRB = OFF 	Boot block (000000-0007FFh) not protected from table reads executed in other blocks